DMX-Abschlusswiderstand 3polA DMX termination resistor will be plugged in the final DMX-device to avoid disruptions by reflections. Specifications  Connector type:3-pol XLR Male  Termination resistor110Ohm with integrated 110Ohm reseistor

 DMX-Abschlusswiderstand 5polA DMX termination resistor will be plugged in the final DMX-device to avoid disruptions by reflections. Specifications  Connector type:5-pin XLR Male  Termination resistor110Ohm

 PixxRangeExtender 5VThe PixxRangeExtender 5V is an optimal tool to receive control signals for digital LED stripes with long signal cables.The signal lines (clock and data) are converted to an interference-insensitive signal,so that increases the range of the signal transmission.For this purpose, the PixxRangeExtender 5V only requires a receiver at the end of the signal line. Specifications  Power supply:5V from digital LED stripe  Connection:3 solder pads for signal input 4 solder pads for connection to LED stripe  Dimensions:23mm x 12mm Product DownloadsPixxRangeExtender 5VBedienungsanleitung PixxRangeExtender 5VUser Manual

 DR-XLR-F3 ServiceanschlussThe DR-XLR-F3 service connector is a 3 pin XLR female connection pre-assembled for top-hat rail mounting.The assignment of the labeled screw terminals corresponds to the assignment of the XLR connection.An integrated 120Ω DMX termination resistor can be activated and deactivated via jumper. Specifications  Connection:Screw terminals XLR-Female  Design:3 pin Pre-assembled on top-hat rail housing base plate  DMX Termination resistor:120 Ohm  Dimensions:35mm x 86mm with locking clip: 35mm x 90mm Product DownloadsDR-XLRBedienungsanleitung DR-XLRUser Manual

 DR-XLR-F5 ServiceanschlussThe DR-XLR-F5 service connector is a 5 pin XLR female connection pre-assembled for top-hat rail mounting.The assignment of the labeled screw terminals corresponds to the assignment of the XLR connection.An integrated 120Ω DMX termination resistor can be activated and deactivated via jumper. Specifications  Connection:Screw terminals XLR-Female  Design:5 pin Pre-assembled on top-hat rail housing base plate  DMX Termination resistor:120 Ohm  Dimensions:35mm x 86mm with locking clip: 35mm x 90mm Product DownloadsDR-XLRBedienungsanleitung DR-XLRUser Manual

<table width="800" cellspacing="1" cellpadding="1">  <tr>    <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;DR-XLR-M3 Serviceanschluss</strong></span></td>  </tr></table><br>The DR-XLR-M3 service connector is a 3 pin XLR male connection pre-assembled for top-hat rail mounting.<br><br>The assignment of the labeled screw terminals corresponds to the assignment of the XLR connection.<br><br>An integrated 120Ω DMX termination resistor can be activated and deactivated via jumper.<br><br><br><img class="dmxmadein" src="https://www.media.dmx4all.store/images/made-in-germany.png" border="0"><br><br><br><!-- Specifications --><table width="800" cellspacing="1" cellpadding="1">  <tr>    <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;Specifications</strong></span></td>  </tr></table><table border="0" cellspacing="1" cellpadding="1">  <tr>    <td width="300">&nbsp;</td>    <td width="500">&nbsp;</td>  </tr>  <tr>    <td>Connection:</td>    <td>Screw terminals</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>XLR-Male</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>&nbsp;</td>  </tr>  <tr>    <td>Design:</td>    <td>3 pin</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>Pre-assembled on top-hat rail housing base plate</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>&nbsp;</td>  </tr>  <tr>    <td>DMX Termination resistor:</td>    <td>120 Ohm</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>&nbsp;</td>  </tr>  <tr>    <td>Dimensions:</td>    <td>35mm x 86mm</td>  </tr>  <tr>    <td>&nbsp;</td>    <td>with locking clip: 35mm x 90mm</td>  </tr></table><br><!-- Produkt Downloads --><table width="800" cellspacing="1" cellpadding="1">  <tr>    <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;Product Downloads</strong></span></td>  </tr></table><div id="dmx4all-buttons"> <a class="document-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/manuals_german/dr_xlr_german.pdf" target="_blank">DR-XLR<br>    <span><span class="german-lang">Bedienungsanleitung</span></span></a>    <br>    <a class="document-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/manuals_english/dr_xlr_english.pdf" target="_blank">DR-XLR<br>    <span><span class="english-lang">User Manual</span></span></a></div>

 DR-XLR-M5 ServiceanschlussThe DR-XLR-M5 service connector is a 5 pin XLR male connection pre-assembled for top-hat rail mounting.The assignment of the labeled screw terminals corresponds to the assignment of the XLR connection.An integrated 120Ω DMX termination resistor can be activated and deactivated via jumper. Specifications  Connection:Screw terminals XLR-Male  Design:5 pin Pre-assembled on top-hat rail housing base plate  DMX Termination resistor:120 Ohm  Dimensions:35mm x 86mm with locking clip: 35mm x 90mm Product DownloadsDR-XLRBedienungsanleitung DR-XLRUser Manual

 PixxRangeExtender 12VThe PixxRangeExtender 12V is an optimal tool to receive control signals for digital LED stripes with long signal cables.The signal line(s) are converted to an interference-insensitive signal,so that increases the range of the signal transmission.For this purpose, the PixxRangeExtender 12V only requires a receiver at the end of the signal line. Specifications  Power supply:12V from digital LED stripe  Output signal:5V control signal  Connection:3 solder pads for signal input 4 solder pads for connection to LED stripe  Dimensions:29mm x 12mm Product DownloadsPixxRangeExtender 12VBedienungsanleitung PixxRangeExtender 12VUser Manual

 DMX-Adressmodul mit LED-DisplayThe DMX-Address module with LED-Display is a helpful additionalmodule which is grinded in the DMX-Line.The DMX-Channels can be shift up as well as down within the DMX-Universes (shiften).The usage occurs via two buttons. The operation mode as well asthe value (DMX-Address) can be adjusted. Specifications  Power supply:5V DC / 50mA  DMX-Input:512 channels  DMX-Output:up to 512 channels  DMX-Output LOAD:Driver for 32 devices (LOAD-UNITs)  Signal delay:~ 0,1µs (Adress-Mode / Shift-Down) ~ 25ms (ChannelAdd-Mode / Shift-Up)  Dimensions:60mm x 30mm Product DownloadsDMX-Adressmodul mit LED-DisplayBedienungsanleitung DMX-Adressmodul mit LED-DisplayUser Manual

 DMX-Merger MK3 2IN/1OUTThe DMX-Merger allows an assemble of two DMX-sources.An usage will be applicable where a total control should occur with several DMX-equipment.If more than two DMX-sources will be assembled a series connection of more than one DMX-Merger is possible. The signal runtime adds in this case. The DMX-Merger assembles the both DMX-lines in a different way.To fix how to work the both inputs on the common output it is possible to adjust the operation mode. Specifications  Power supply:7-24V DC / 200mA  Input:2x 512 channels  Output:512 channels  Modes:Higest value Lowest value Last changed value Last changed universe Add of both value Combine Backup  Dimensions:64,2mm x 82 mm Product DownloadsDMX-Merger MK3 2IN/1OUTBedienungsanleitung DMX-Merger MK3 2IN/1OUTUser Manual DMX-Merger MK3 2IN/1OUTUSB Driver 32 & 64bit - Version 6.0.0.0 DMX-Merger MK3 2IN/1OUTFirmware

 DMX-Audio UnitThe DMX Audio Unit is designed to play audio files in mp3 format.64 Audio FilesVia DMX up to 64 audio files can be called via one DMX channel.USB Data MediumThe MP3 audio files are stored on a USB data medium and easily exchangeable.Several Operation ModesDepending on the application, the DMX Audio Unit offers different operating modes.Either 32 or 64 audio files can be called directly or via up/down the audio files can be played back in line.Playback SINGLE PLAY / LOOP PLAY / CYCLE PLAY / PAUSE / STOPPlayMode is used to start playback, put the playback into a repeat loop or pause and stop to stop the replay.Settable Playback VolumeThe playback volume can be adjusted via a DMX channel.Settable Accoustic ColourThe acoustic colour (EQ) can be adjusted between five predefined settings.Power supply 8V up to 24VThe DMX Audio Unit can be operated with 8V up to 24V DC.DMX FAIL-FunctionAn adjustable DMX FAIL function offers the option to hold the current state (HOLD),turn off playback (OFF), or to operate a previously set state in the event of a failed DMX signal.RDM SupportThe DMX Audio Unit allows configuration via RDM over DMX.Direct access to the device is not necessary. Via RDM, the settings can be made comfortable from distance.Compact DimensionsThe compact dimension of 29,2mm x 82mm allows the installation on a top hat rail housing with only 35mm width.Top hat rail mountingThe top-hat rail housing 350 or the top-hat rail housing 350flat are available as equipment for the DMX Audio Unit. Specifications  Power supply:8-24V DC  Power consumption:100mA@12V / 70mA@24V  Protocol:DMX512 RDM  DMX channels:4 or 5 channels (depends on operation mode)  DMX-FAIL:HOLD / OFF / Perdefine  Operation modes:32Songs/PlayMode/Vol/EQ 64Songs/PlayMode/Vol/EQ SongUp/SongDown/PlayMode/Vol/EQ  Play Mode:Single Play Loop Play Cycle Play Pause Stop  Acoustic color (EQ):Normal Pop Rock Jazz Classic  Output:Line Out (R+L)  Data medium:USB stick  File format:mp3  Connections:screw terminals USB-A 3,5mm Plug  Dimensions:29,2mm x 82mm  Content:DMX-Audio Unit USB stick 4GB Quick guide german and english Produkt DownloadsDMX-Audio UnitBedienungsanleitung DMX-Audio UnitUser Manual

 DMX-Splitter 4The DMX-Splitter 4 is a compact DMX-Divider with one DMX-Input signal which providesthese at four galvanically isolated outputs.4 galvanically isolated outputsThe DMX-Splitter 4 is a compact DMX-Divider with one DMX-Input signal which providesthese at four galvanically isolated outputs.Extremely light constructionExtremely light DC/DC converters are used for galvanic isolation.Power supply via one power supply unitThe power supply occurs via one power supply unit.The voltage range is between 8V up to 24V.Compact design for top hat rail mountingThe DMX-Splitter 4 is suitable for installation in top hat rail mountingswith a width of 7cm due to its small size.LED-DisplayTwo LEDs show clearly the current operation mode.Top hat rail mounting availableSuitable for the DMX Splitter 4 the DIN rail housing 700 is available as accessory. Specifications  Power supply:8-24V DC (350mA@12V; 200mA@24V)  Input:512 channels  Output:4x 512 channels galvanically isolated  Connections:screw terminals  Dimensions:64,2mm x 82mm Product DownloadsDMX-Splitter 4Bedienungsanleitung DMX-Splitter 4User Manual

<table width="800" cellspacing="1" cellpadding="1"> <tr> <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;PixxSplitter DR8</strong></span></td> </tr></table><br>The PixxSplitter DR8 is a manifold for a digital LED signal to up to 8 connected digital LED-Strips.<br><br>Up to 999 RGB or RGBW pixels can be connected to each output.<br><br>The input signal, coming from a pixel controller, contains control information for all connected pixels.<br>This allows to control up to 8 different digital LED-Strip elements with just one control unit. The wiring is radial.<br><br><br>In the Default-Setting, the number of pixels on each output is set to 100 RGB pixels.<br>In total a pixel controller drives 800 RGB pixels, whereby the first 100 pixels (pixels 1-100) are connected to output 1,<br>the second 100 pixels (pixels 101-200) to output 2, etc.<br><br><br><img class="dmxmadein" src="https://www.media.dmx4all.store/images/made-in-germany.png" border="0"><br><br><br>　<table width="800" cellspacing="1" cellpadding="1"> <tr> <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" border="0" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;Specifications</strong></span></td> </tr></table><table border="0" cellspacing="1" cellpadding="1"> <tr> <td width="300">&nbsp;</td> <td width="500">&nbsp;</td> </tr> <tr> <td>Power supply:</td> <td>8-24V / 100mA</td> </tr> <tr> <td>&nbsp;</td> <td>5V / 100mA via Mini-USB connector</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Input:</td> <td>Control signal for digital LED stripes</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Output:</td> <td>8x control signal for digital LED stripes</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Compatible LED-Types:</td> <td>SK6812</td> </tr> <tr> <td>&nbsp;</td> <td>GS8208</td> </tr> <tr> <td>&nbsp;</td> <td>WS2811, WS2812(B)</td> </tr> <tr> <td>&nbsp;</td> <td>INK1002, INK1003</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Color sequence:</td> <td>RGB / RGBW (selectable)</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Number of pixel/output:</td> <td>1 - 999 pixel</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Display:</td> <td>3 digit 7 segment display</td> </tr> <tr> <td>&nbsp;</td> <td>8x LED</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Controls:</td> <td>3 buttons (UP / DOWN / SELECT, SET)</td> </tr> <tr> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td>Dimensions:</td> <td>99mm x 82mm</td> </tr></table><br><br>　<table width="800" cellspacing="1" cellpadding="1"> <tr> <td><img src="https://www.media.dmx4all.store/images/kategorie-head.png" align="absmiddle"><span style="font-size: large;"><strong>&nbsp;Produkt Downloads</strong></span></td> </tr></table><div id="dmx4all-buttons"><a class="document-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/manuals_german/pixx_splitter_dr8_german.pdf" target="_blank">PixxSplitter DR8<br> <span><span class="german-lang">Bedienungsanleitung</span></span></a> <br> <a class="document-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/manuals_english/pixx_splitter_dr8_english.pdf" target="_blank">PixxSplitter DR8<br> <span><span class="english-lang">User Manual</span></span></a> <br> <a class="drivers-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/drivers/driver_x32_x64_pixx_splitter_dr8.zip">PixxSplitter DR8<br> <span><span class="windows-os">USB Driver</span></span></a> <br> <a class="firmware-button" onfocus="this.blur()" href="https://www.dmx4all.de/download/firmware/firmware_pixx_splitter_dr8.zip">PixxSplitter DR8<br> <span><span class="firmware-os">Firmware</span></span></a></div>

 DMX-Splitter 6The DMX-Splitter 6 is a compact DMX-Divider with one DMX-Input signal which providesthese at six galvanically isolated outputs.6 galvanically isolated outputsThe DMX-Splitter 6 is a compact DMX-Divider with one DMX-Input signal which providesthese at four galvanically isolated outputs.Extremely light constructionExtremely light DC/DC converters are used for galvanic isolation.Power supply via one power supply unitThe power supply occurs via one power supply unit.The voltage range is between 8V up to 24V.Compact design for top hat rail mountingThe DMX-Splitter 6 is suitable for installation in top hat rail mountingswith a width of 10,5cm due to its small size.LED-DisplayA multicolor LED clearly indicates the current operating status.Top hat rail mounting availableSuitable for the DMX Splitter 6 the DIN rail housing 1050 is available as accessory. Specifications  Power supply:8-24V DC (350mA@12V; 200mA@24V)  Input:512 channels  Output:6x 512 channels galvanically isolated  Status Display:Multi-color LED  Connections:screw terminals  Dimensions:99mm x 82mm Product DownloadsDMX-Splitter 6Bedienungsanleitung DMX-Splitter 6User Manual

 DMX-Splitter 4 RDMThe DMX-Splitter 4 RDM is a compact DMX and RDM distributor that makes a DMX input signalavailable again at four galvanically isolated outputs.4 galvanically isolated outputsThe DMX-Splitter 4 RDM is a compact DMX and RDM distributor that makes a DMX input signalavailable again at four galvanically isolated outputs.DMX and RDMIn contrast to pure DMX splitters, the RDM information is passed in bothdirections in addition to the DMX signal.RDM filterWhen the RDM filter is switched on, all RDM information are filtered out and no longer passedon to the outputs. This can prevent malfunction / flickering of non-RDM-capable devices.Settings possible via RDMThe DMX-Splitter 4 RDM is recognized as an independent RDM device and settings can be made via RDM.Extremely light constructionExtremely light DC/DC converters are used for galvanic isolation.Power supply via one power supply unitThe power supply occurs via one power supply unit. The voltage range is between 8V up to 24V.RGB-LED-DisplayThree RGB LEDs clearly indicate the current operating status.Top hat rail mounting availableSuitable for the DMX-Splitter 4 RDM the DIN rail housing 700 is available as accessory. Specifications  Power supply:8-24V DC  Power consumption:200mA@12V / 130mA@24V (no load)  Protocol:DMX512 RDM  Output:4x DMX512 / RDM galvanically isolated  RDM filter:Can be switched on / off  Connections:screw terminals  Dimensions:64,2mm x 82mm Product DownloadsDMX-Splitter 4 RDMBedienungsanleitung DMX-Splitter 4 RDMUser Manual

 DMX-Splitter 6+The DMX-Splitter 6+ is a compact DMX-Divider with one DMX-Input signal which providesthese at six galvanically isolated outputs.6 galvanically isolated outputsThe DMX-Splitter 6+ is a compact DMX-Divider with one DMX-Input signal which providesthese at four galvanically isolated outputs.Extremely light constructionExtremely light DC/DC converters are used for galvanic isolation.Power supply via one power supply unitThe power supply occurs via one power supply unit.The voltage range is between 8V up to 24V.Compact design for top hat rail mountingDue to its small size, the DMX Splitter 6+ is suitable for installationon DIN rails with a width of 10.5 cm.LED-DisplayA multicolor LED clearly indicates the current operating status. Specifications  Power supply:8-24V DC (350mA@12V; 200mA@24V)  Input:512 channels  Output:6x 512 channels galvanically isolated  Status Display:Multi-color LED  Connections:screw terminals  Dimensions:105mm x 90mm x 60mm Product DownloadsDMX-Splitter 6+Bedienungsanleitung DMX-Splitter 6+User Manual

 DMX-Splitter 4 RDM+The DMX-Splitter 4 RDM+ is a compact DMX and RDM distributor that makes a DMX input signalavailable again at four galvanically isolated outputs.4 galvanically isolated outputsThe DMX-Splitter 4 RDM+ is a compact DMX and RDM distributor that makes a DMX input signalavailable again at four galvanically isolated outputs.DMX and RDMIn contrast to pure DMX splitters, the RDM information is passed in bothdirections in addition to the DMX signal.RDM filterWhen the RDM filter is switched on, all RDM information are filtered out and no longer passedon to the outputs. This can prevent malfunction / flickering of non-RDM-capable devices.Settings possible via RDMThe DMX-Splitter 4 RDM is recognized as an independent RDM device and settings can be made via RDM.Extremely light constructionExtremely light DC/DC converters are used for galvanic isolation.Power supply via one power supply unitThe power supply occurs via one power supply unit. The voltage range is between 8V up to 24V.3 RGB-LEDsThree RGB LEDs clearly indicate the current operating status.Touch-ControlThe DMX-Splitter 4 RDM+ has an integrated touch control field to turn on/off the RDM filter. Switchable LED-DisplayThe LED-Display at the DMX-Splitter 4 RDM+ can be switched off via RDM command or time-controlled,so that no disturbing light sources are present during operation. Specifications  Power supply:8-24V DC  Power consumption:200mA@12V / 130mA@24V (no load)  Protocol:DMX512 RDM  Input:1x DMX512 / RDM  Output:4x DMX512 / RDM galvanically isolated  RDM filter:Can be switched on / off  TOUCH-Control:1 sensor button directly on the device and 3 RGB status LEDs  Connections:screw terminals  Dimensions:70mm x 90mm x 60mm Product DownloadsDMX-Splitter 4 RDM+Bedienungsanleitung DMX-Splitter 4 RDM+User Manual